XY-J03 1-Way Relay with Casing Delayed Power Outage Trigger Delayed Cycle Timer Switch

Relays1Circuit relay moduleWith shellDelayed power-off and disconnection trigger delayed cycle timer switch0.1Seconds (min)~999Minute (maximum) adjustableWith a transparent shell, safe and reliable, beautiful and generous!This product is easy to use and powerful, but please look at the operation instructions of this product in detail. It is a very practical product. highlights:1. Wide voltage supply(6~30V)Supportmicro USB 5.0Vpower supply, very convenient to use;2. The interface is clear and simple, powerful and easy to understand, which can meet almost all your needs;3.It has one key emergency stop function(stopKey), with reverse connection protection, reverse connection does not burn;4.Added sleep mode, after enabling,5If there is no operation within minutes, the display will be turned off automatically; Wake up by pressing any key;5.You can set different settingsOn,CL,LopParameters, which are independent of each other and saved separately;6.All setting parameters are automatically saved after power failure.Working mode:P1mode: When the signal is triggered, the relay turns onOnTime, and then disconnect; inOnWithin the time, the following operations shall be carried out:P1.1:The signal is triggered againinvalidP1.2:The signal is triggered againRe P1.3:The signal is triggered againreset, the relay is disconnected and the is stopped;P-2: the trigger signal is given and the relay is disconnectedCLAfter time, the relay turns onOnTime, after the is completed, disconnect the relay;P3.1: give a trigger signal and turn on the relayOnAfter time, the relay opensCLTime, then cycle the above actions, give a signal again in the cycle, the relay is disconnected and the is stopped; cycle times(Lop)Can be set;P3.2: no trigger signal is required after power on, and the relay is onOnTime, relay offCLTime, cycle the above actions; number of cycles(Lop)Can be set;p-4: signal holding function If there is a trigger signal, the is cleared and the relay remains on; when the signal disappears, the is resetOnAfter that, disconnect the relay; during the , if there is another signal, the will be cleared;Product parameters:1: operating voltage:6--30VSupportmicro USB 5.0Vpower supply2: trigger signal : high level trigger(3.0v-24V)The signal ground and system ground are not grounded together to improve the anti-interference ability of the system (or short-circuit common ground by itself)3: Output capacity: can be controlled30V5AInternal or communication220v5AEquipment within4: Quiescent current:20mA Working current:50mA5: Service life: more than1010000 times; Operating temperature:-40-85; size:6.2*3.8*1.7cm6With optocoupler isolation, enhance anti-interference ability, industrial grade circuit board, set parameters after power failure foreverMemory.Special attention:The relay output is a passive contact, which has no live output and controls the on-off of a line. range0.1Seconds (min)~999Minute (maximum) adjustableHow to select range:stayMode selection interfacePass after setting the parameter valueShort pressstopkey, select the range;XXX.The decimal point is in digits, and the range is:1second~999secondXX.XThe decimal point is in ten digits, and the range is:0.1second~99.9secondX.X.X.The decimal point is fully lit, and the range is:1Minute~999MinuteFor example, you want to setOnis3.2Seconds, then move the decimal point to the tenth place, and the nixie tube displays it03.2Parameter Description:OnOn time,CLDisconnection time,LopNumber of cycles(1-999Times,"---"(for infinite cycles)These parameters are independent of each other, but they are common to all modes,For example, inP1.1The on time is setOnis5Second, the user wants to switch toP1.2Mode, then enterP1.2When setting corresponding parameters,OnIt will be5Second;In the main interface (display)000)Short presssetKey, theOn(CL,Lop)And corresponding time XXX company;If onlyOn(e.g. mode)P1.1,P1.2,P1.3)In case of time, press brieflysetThe key will only showOnAnd corresponding timeA kind ofIf there is in the modeOn,CL,Lop(e.g. mode)P3.1,P3.2)That short presssetThe key will be displayedOnAnd corresponding time,CLAnd corresponding time,LopAnd corresponding times;After setting the mode, press briefly on the main interfacesetThe key allows you to easily view the parameters set in the current mode, which is very convenient!How to set parameters1. Firstly, the working mode of the relay is determined;2. According to the working mode of the relaymain interface(when the is powered on, it will flash the current working mode (default)P1.1Mode), and then entermain interface,)"Long presssetkey2Release in seconds"EnterMode selection interface, by briefly pressingUp,downPress the key to select the mode to be set(P1.1~P-4);3.After selecting the mode to be set (e.gP3.2)Short presssetkeySet the corresponding parameters, and the parameters to be set will flash(OnOn time,CLDisconnection time,LopNumber of cycles("---"Represents an infinite number of cycles), byUp,downAdjust parameter values, support long press (fast increase or decrease) and short press (increase or decrease)1Units); after setting the parameter value, passShort pressstopkeyTo select the decimal point position and range(Corresponding time0.1second~999Minute); press brieflysetKey to set the next parameter of the current mode. The process is the same as above;4.After setting the parameters of the selected mode,Long presssetkey2secondAfter releasing, the currently set mode will flash, and then to the main interface. The parameter setting is successful, very simple!main interface:Display when the relay is not working"000"(No decimal point), the relay has a decimal point in its working state, very clear!Mode selection interface: long presssetKey to enter. After setting, press and holdsetKey to exit and to the main interface, very simple!stopKey function expansion:Relay enable mode:1. on :OnThe relay is allowed to conduct during the conduction time;2. off: The relay is prohibited from conducting and is always closed;In the main interfaceShort pressstopPress the key to realizeonandoffWhen switching between, the current state will flash, and then to the main interface. (this function is an emergency stop function, which opens the closed relay with one key)Sleep mode:1. C-PSleep mode: within five minutes, without any operation, the nixie tube automatically turns off the display, and the program runs normally;2. O-dNormal mode: nixie tube always turns on display;Long pressstopKey2Release after seconds to achieveC-PandO-dState switching, the current state will flash, and then to the main interface.

• Relays
• XY-J03 1-way Relay With Casing Delayed Power Outage Trigger Delayed Cycle timer switch